Installing the FRC 2018 Update Suite (All Languages)

The FRC 2017 Update Suite contains the following software components: LabVIEW Update, FRC Driver Station, and FRC Utilities. If an FRC 2017 LabVIEW installation is found, the LabVIEW Update will be installed or updated, otherwise this step will be skipped. The FRC Driver Station and FRC Utilities will always be installed or updated. The LabVIEW runtime components required for the driver station and utilities is included in this package. No components from the LabVIEW DVD are required for running either the Driver Station or Utilities.

C++ and Java teams wisinhg to use NI Vision Assistant should run the full DVD installer as described in the article - Installing LabVIEW for FRC 2017 (LabVIEW only)

Note: The 2017 DS will only work on Windows 7, Windows 8, Windows 8.1, and Windows 10. It will not work on Windows XP.

LabVIEW Teams: CAN Talon SRX has been removed from WPILib. See this blog for more info and find the CTRE Toolsuite installer here: http://www.ctr-electronics.com/control-system/hro.html#product_tabs_technical_resources

Uninstall Old Versions (Recommended)

LabVIEW teams have already completed this step, do not repeat it. Before installing the new version of the NI Update it is recommended to remove any old versions. The new version will likely properly overwrite the old version, but all testing has been done with FRC 2018 only. Make sure to back up any team code located in the "User\LabVIEW Data" directory before un-installing. Then click Start >> Control Panel >> Uninstall a Program. Locate the entry labeled "National Instruments Software", right-click on it and select Uninstall/Change.

Select Components to Uninstall

Select Components to Uninstall

In the left pane of the dialog box that appears, select all entries. The easiest way to do this is to click the top entry to highlight it, then scroll down to the bottom entry, press and hold shift and click on the last entry then release shift. Click Remove. Wait for the uninstaller to complete and reboot if prompted.

Downloading the Update

Windows 8

Windows 8

If installing on Windows 8 or 10 and the above error appears, jump down to the Addendum on Windows 8 installation before returning here to re-start the installation.

Welcome

Welcome

RIght click on the downloaded zip file and select Extract All. If you downloaded the encrypted zip file, you will be prompted for the encryption key which will be released at Kickoff. Open the extracted folder and any subfolders until you reach the folder containing "setup" (may say "setup.exe" on some machines). Double click on the setup icon to launch the installer. Click "Yes" if a Windows Security prompt appears. Click "Next" on the splash screen that appears.

Product List

Product List

Click "Next"

Product Information

Product Information

Un-check the box, then Click "Next"

User Information

User Information

Enter full name and organization and the serial number from your kit of parts then click Next

License Agreements

License Agreements

Select "I accept..." then click "Next"

License Agreements Page 2

License Agreements Page 2

Select "I accept..." then click "Next"

Summary Progress

Summary Progress

Detail Progress

Detail Progress

Installation Summary

Installation Summary

Make sure the box is checked to Run License Manager... then click Next

Activate

Activate

Select your desired activation method (Internet activation recommended), then click Next

Serial Number Confirmation

Serial Number Confirmation

Log into the NI Licensing Wizard, then enter the serial number from your LabVIEW packet from the Kit of Parts.

Finish Installation

User Profile

After the product has activated successfully, click Next.

Finish Installation

User Profile 2

Click Close.

NI Update Service

NI Update Service

On occasion you may see alerts from the NI Update Service about patches to LabVIEW. It is not recommended to install these patches. FRC will communicate any recommended updates through our usual channels (Frank's Blog, Team Updates or E-mail Blasts).

Addendum - Installing on Windows 8

If installing on Windows 8 or 10, the Microsoft .NET Framework 3.5 may need to be installed. If you see the dialog shown above, click "Cancel" and perform the steps shown below. An internet connection is required to complete these steps.

Programs and Features

Open the "Programs and Features" window from the control panel and click on "Turn Windows features on or off"

Windows Features (.NET Framework 3.5 not on)

Windows Features (.NET Framework 3.5 not on)

Select ".NET Framework 3.5 (includes .NET 2.0 and 3.0)" to enable it (a black dot, not a check box will appear) and then click "OK". When installation finishes restart installation of FRC 2016 Update Suite.

Windows Features (.NET Framework 3.5 already on)

Windows Features (.NET Framework 3.5 already on)

If a black dot is shown next to ".NET Framework 3.5" the feature is already on. Click "Cancel" and restart installation of FRC 2017 Update Suite.

0 Report Errors

Use this form to report any errors with the documentation. For help with WPILib, please use the FIRST Forums at http://forums.usfirst.org For reporting WPILib bugs, please submit an issue on GitHub at https://github.com/wpilibsuite/allwpilib/issues/new

Ignore